333modules - Integrator DJ
only 1 left
Input module with DJ influence, RCA in and selectable line and phono input (RIA filter), with three modular level outputs Left, Right and Mono sum. Level gain with fader volume for live purposes.Features:• RCA input• Phono (RIA) or line• Gain and fader volumen• Stereo a Mono sum Output modular levelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
%
4ms - Percussion Interface & Expander
available
The Percussion Interface (PI) and PI Expander are a pair of Eurorack modules that generate gates and envelopes from acoustic drums, samplers, drum machines, and virtually any audio source.Converting microphone, instrument, line and modular signals into CV and clock/gate signals, the PI and PI Expander are suited for synchronizing sequencers or other modules to the rhythm of an audio track or live percussion. The modules can simultaneously be used as a pre-amp for microphones or line-level signals, while generating inverted envelopes useful for side-chaining. The PI module contains all the core functionality and can be used without the Expander to conserve space. The Expander requires the main PI modules and adds three gain stage options, a modular-level audio output jack, a 1/4" (6.35mm) input jack, and envelope attenuation capabilities. The two modules are only sold together, they are not available separately.Features:• Sensitivity knob, Low/Medium/High gain switch, and clipping LED• Sustain control to prevent misfires, increase gate length, and control the envelope• Envelope decay control• Non-inverted and inverted envelope outputs, useful for side chaining• Four envelope outputs: two attenuated with independent attenuators, and two non-attenuated• Envelope following or generation modes• Gate output for clocking sequencers or any unit with a clock or trigger input• Compatibility with drums, pads, samplers, microphones, piezos, drum machines, etc.• 1/8" or 1/4" input jack (6.35mm)
€124.95*
€173.70*
(28.07% saved)
ADDAC System - 200 Pedal Integrator
only 1 left
This small utility is the pedal lover's best friend, it allows 2 diferent chains of pedals to be independently connected to your synth.The Send channels attenuate the synth level to instrument level.The Return channels amplify the signal from instrument to synth level.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€83.50*
ADDAC System - 213A Eurorack Bridge
available
The first modules from our Eurorack Bridge system!A pair of ADDAC213As acts as a simple one-cable bridge between different cases. By itself the ADDAC213As can send/receive 8 CV or audio signals between your cases, but can be expanded to bridge two cases for up to 24 signals at the same time.Use a pair of ADDAC213As to send & receive 8 CV or audio signals between distant points in your case, between two separate cases, or between your case and a friend's case. Less clutter, less spaghetti, faster connection! There’s nothing better than being able to connect that controller skiff with just one cable to your main system. At a gig, in the studio, when jamming with a friend, give yourself a gift by grabbing a pair of ADDAC213As. The modules can be installed in normal position or a 180 degree position to fit any need and any case design.Expansion by the ADDAC213BsEach ADDAC213A module can be connected through a ribbon cable connection on its backside with up to two ADDAC213Bs. Each ADDAC213B module added expands the channels options of the ADDAC213A by adding 8 more channels. With two ADDAC213Bs connected to each ADDAC213A module, you’ll have a total of 24 channels going between your cases with a simple one-cable bridge. Between the ADDAC213A pair and the ADDAC213B, your cases never looked so elegantly connected together!The ADDAC213As are always sold as a pair of 2 modules and an included ribbon cable (50cm or 100cm ribbon cable, or custom sizes available upon request).Each module can be installed in normal position or at 180 degrees.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€95.00*
ADDAC System - 213B Eurorack Bridge EXP
available
The ADDAC213B is the second pair of modules from our Eurorack Bridge system!A pair of ADDAC213Bs can be used in standalone to send/receive 8 CV or audio signals between different points inside the same case or as an expansion to the main pair of Eurorack Bridge modules, the ADDAC213As.Standalone use:Two ADDAC213B modules can be connected to each other with the use of a single ribbon cable and then used inside a case to carry signals between distant points without the need for long cables. Less clutter, less spaghetti, more space of your fingers on those knobs!ADDAC213Bs always come in pairs. A single pair can send & receive up to 8 CV or audio signals between different points in your case at the same time. The modules can be installed in normal position or a 180 degree position to fit any need.Do you have modules that you often use together in different areas of your case? Would you prefer that each row’s cables don’t mingle with cables from other rows? Grab yourself a pair of ADDAC213s.As an Expansion to an ADDAC213A:Each ADDAC213B connected to the backside of an ADDAC213A adds 8 more channels to the main bridging functionality of the ADDAC213A.Up to 2 ADDAC213B can be connected to an ADDAC213A module, expanding the bridging between two difference cases to a total of 24 channels.If you’re looking for a simple one-cable bridge between your various cases, then look no further than the ADDAC213A.Between the ADDAC213A pair and the ADDAC213B, your cases never looked so elegantly connected together!Each module can be installed in normal position or at 180 degrees.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€80.00*
ADDAC System - 214 VC Rotator
available
This is our VC Rotator, a stepped routing module for any type of signal (audio, cv, gate, trigger...)Similar to a VC switcher but in this case there's the same number of inputs as outputs so, instead of 4 to 1 or 1 to 4, this module is always 4 to 4 but it can be patched for 2 to 2 and 3 to 3 step actions.All four inputs get routed to the four outputs depending on the CV and Clock controls and are divided into 4 routing steps:1. routes all inputs to the same number output: 1:1, 2:2, 3:3, 4:42. routes all inputs to an offset of 1: 2:1, 3:2, 4:3, 1:43. routes all inputs to an offset of 2: 3:1, 4:2, 1:3, 2:44. routes all inputs to an offset of 3: 4:1, 1:2, 2:3, 3:4Direction determines if the clock input goes forward or backwards.Going forward it can be set to 2-3 or 4 steps using the Rotate knob offset, going backwards always sync to 4 steps even if offseted by the Rotate knob.For 2 & 3 step action input 1 is normalled to input 3 and input 2 is normalled to input 4.Reset resets the internal clock to the first step.Pendulum, external sequencing or any complex CV actions can be achieved using the CV input and dedicated attenuverter.4 LEDs monitor which input is routed to output 1.Features:• 4 Inputs• 4 Outputs• Direction Switch• CV Rotate with Attenuverter• Clock and Reset Inputs• 4 Monitor LedsDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€145.00*
ADDAC System - 304 Manual Gates
available
With the ADDAC304 Manual Gates you'll be getting 8 manual gates (0 +5v) in a nifty package - a perfect way to perform on and control your modular system.The ADDAC304 comes with an interesting twist: 4 out of the 8 available gates can act as momentary switches, outputting the signals in their respective inputs when each gate’s button is pressed.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€75.00*
ADDAC System - 305 Manual Latches
available
The ADDAC305 Manual Latches is a combination of 8 manual latching switches in a small and elegant module: each button toggles between Gate high / Gate low when pressed, outputting a 5V gate signal. Additionally, 4 of the 8 available latches sport inputs and can act as manual latching switches, allowing the incoming signal to pass to the output when the button is toggled.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€90.00*
ADDAC System - 306 VC Transitions
only 1 left
ADDAC306 is a 5 channel multi-directional CV generator.You can think of it as a "sweet spot" controller, or a hands-on way of transiting from one state to another.Each of the five channels has MINIMUM, SPAN and DIRECTION controls, a common CV IN and a common TRANSITION CONTROLLER slider.MINIMUM sets the minimum channel voltage.SPAN sets the voltage range of the channel.It essentially sets the maximum voltage that can be output from the channel, relative to what the current channel MINIMUM is. For a given SPAN value, if the MINIMUM voltage is changed then the maximum voltage output from that channel will also change respectively.DIRECTION sets whether the voltage transition for each channel goes from MINIMUM to maximum, or maximum to MINIMUM.The TRANSITION CONTROLLER slider controls the transition from the minimum value (A) to the maximum value (B) or vice versa, according to the settings of each independent channel.Moving this slider generates 5 different voltages with 5 different ranges and directions. The transition can also be operated from a CV source at the CV IN, in which case the slider position acts as an attenuator for the incoming voltage.The maximum range of each channel can be set to either 5 or 10 volts, by 5 jumpers in the back of the module. Only positive voltages are generated at the output.Using the CV IN you can use two ADDAC306 modules to expand your control options to 9 voltage outputs under one common slider control.Use the VC Transitions to multiply the polyphony of a single CV sequencer by passing its outputs through the ADDAC207.VC Transitions makes for an awesome state transition controller. Plug its outputs to various CV controller parameters of your audio effects modules. Set the slider to position A, and set the minimum values for each channel. Then move the slider to position B and set the SPAN settings for each channel. Use the TRANSITION CONTROLLER slider to morph from state A to state B and backwards. Flip the DIRECTION switches to change the direction of the transition for each channel. Use the CV IN to automate the transition using LFOs, ADSRs or sequencers.Plug the output of your ADSR envelope to the CV IN and set the channels differently to get 5 different ADSRs from one common source.This module's development was based on an initial idea by Konstantine Fioretos.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€113.90*
ADDAC System - 308 Light to CV
available
Another addition to our ADDAC300’s Expressive Controls series. This module converts the incoming light hitting an external light sensor into 2 Bipolar CV Streams:Output: More light > Higher CV outputInverted Output: More light > Lower CV outputThe external sensor is enclosed in a jack socket in order to be used with any standard jack cable and be able to place it in any place outside the Eurorack frame.There are several controls to adjust the CV Output’s signals:• Sensitivity: Adjusts the Light Sensor sensitivity to Light. The Higher the sensitivity the better it responds to low light situations.• Response: 3 fixed settings (medium/fast/slow) to set the slew applied to the raw signal coming from the sensor.• Gain: Sets the gain for both outputs• Offset: Adjusts the Offset for the main Output.• Inverted Offset: Adjusts the Offset for the Inverted Output.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€101.00*
ADDAC System - 309 CV To Expression
available
ADDAC309 CV to Expression allows a simple and straight forward connection between modular and effect pedals that features expression pedal TRS inputs.Instead of using an expression pedal into the effects pedal the user can use this module in between a CV source and the effects pedal to be controlled. This is a great way to control the available parameters on the effects pedals straight from a CV source.ADDAC309 features 2 channels each with a CV input with attenuator and a 1/4" jack output.This is a passive module, the power needed for operation is taken from the pedal power instead of the modular frame, this allows for perfect matching of the pedal’s operating voltage which can range from 3,3 V to 9 V.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€49.00*
ADDAC System - 805 VC Signal Router V2
available
Inspired by our ADDAC701 VCO waveform mixing section, our new VC Signal Router also updates our legacy X-Fade/Panner to a stereo configuration that also allows 4 quadrant mixing.Featuring two dedicated X-faders and a stereo VCA that can also be used as a third X-Fader. All controls have their own CV inputs and dedicated Attenuverters for precision control.4 quadrant mixing is achieved by using the stereo Master as a X-fader between left and right channels, this way you can plug 4 audio sources and sweep/crossfade between each and any of them using the 3 x-faders. Plug any 4 sources (4 waveforms of a VCO, 4 LFOs, 4 envelopes...) and sweep through morph through or have them all mixed together.For other configuration types Left and Right X-fader channels can be routed through the Master stereo VCA or sent directly to the outputs. A stereo Direct input can also be routed through the Master VCA or sent straight to the outputs.The Mono Sum output always mix Left and Right outputs together allowing the possibility to use the module as a peculiar 6 channel mono mixer.It can be used for both Audio or CV Signals.Features:• 6 mono inputs• 2 dedicated X-faders with Control knob + CV Input and Attenuverter Each X-fader can be routed through the Master mix or straight into the outputs.• Master channel can be used as a stereo VCA or an X-fader• Stereo direct inputs can be routed through the Master mix or straight into the outputs.• Fully analog audio path with high quality/low noise VCAs.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€168.90*
Allen Synthesis - EuroPi
only 1 left
Reprogrammable Multi-Function Controller based on the Raspberry Pi PicoThe EuroPi is a project aimed at making Eurorack more accessible and customisable by giving users complete control of the inner workings of a digital module.You can plug the module into your computer using a standard micro USB cable, and entirely re-write the program in Python (https://www.python.org) usingany of the inputs and outputs for whatever you want. It can be used to replicate existing concepts, such as a quantiser or sample and hold, or you can write something entirely new.All of the information about this project can be found on the GitHub Repository. This includes the build guide, bill of materials, license details, and firmware.There is also a Subreddit if you'd like to share your builds, ask any questions, or just join the community!Features:• 6 CV Outputs (0-10V)• 1 CV Input (0-10V)• 1 Digital Input (Clock, Gate, Trigger)• 2 Knobs (12 bit)• 2 Push Buttons• 128x32 OLED DisplayDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€136.85*
AtoVproject - 16n Rework (Black)
only 1 left
The 16n AtoVproject Rework is aimed at solving a problem very specific to modular synthesis. As a patch is getting more and more complex a forest of cables has grown over your system before you know it. This module allows you to take the control from the modular into a very ergonomic controller that integrates perfectly into a modern studio.The 16n AtoVproject Rework is a controller sending CV, I2C, MIDI jack, USB MIDI (compatible PC, Mac, iPad etc...), making it the absolute ultimate controller for any of your hardware and software all in one!Even better this controller can either be used as a Eurorack module or as a standalone unit using the beautiful aluminum enclosure.In 2019, the Berlin Modular community showed interest in building the 16n Faderbank. As one of the Berlin Modular community organizers, I decided to make a redesign of the 16n faderbank following the suggestions and desires of our members. The 16n AtoVproject Rework is the result.Features:• 16 high-end Alps faders• Eurorack compatible (50hp) and standalone enclosure (for use in or out of the rack)• Selectable 0-5V or 0-10V CV output range (independent setting for each fader)• High stability power conditioning for high stability analog outputs• Soft MIDI thru. MIDI data sent to the 16n through USB is echoed to the MIDI jack (Since firmware v2.1.0)• Utility connector on the back of the unit to simplify the use of i2c with modules like the ER301DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€279.00*
AtoVproject - 16n Rework (Silver)
sold out at the moment
The 16n AtoVproject Rework is aimed at solving a problem very specific to modular synthesis. As a patch is getting more and more complex a forest of cables has grown over your system before you know it. This module allows you to take the control from the modular into a very ergonomic controller that integrates perfectly into a modern studio.The 16n AtoVproject Rework is a controller sending CV, I2C, MIDI jack, USB MIDI (compatible PC, Mac, iPad etc...), making it the absolute ultimate controller for any of your hardware and software all in one!Even better this controller can either be used as a Eurorack module or as a standalone unit using the beautiful aluminum enclosure.In 2019, the Berlin Modular community showed interest in building the 16n Faderbank. As one of the Berlin Modular community organizers, I decided to make a redesign of the 16n faderbank following the suggestions and desires of our members. The 16n AtoVproject Rework is the result.Features:• 16 high-end Alps faders• Eurorack compatible (50hp) and standalone enclosure (for use in or out of the rack)• Selectable 0-5V or 0-10V CV output range (independent setting for each fader)• High stability power conditioning for high stability analog outputs• Soft MIDI thru. MIDI data sent to the 16n through USB is echoed to the MIDI jack (Since firmware v2.1.0)• Utility connector on the back of the unit to simplify the use of i2c with modules like the ER301DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€279.00*
AtoVproject - MMx2
available
Expand the power of your modulations with the MMx2, a dual-pack module designed to bring flexibility and creativity into your system. Each MMx2 package contains a pair of MM modules.Sold as a pair, MM modules can function as two separate units or be linked for expanded matrix mixing capabilities. Connect even more MM modules to increase the power of your Eurorack synthesiser!Every MM module has attenuator on the first two inputs and attenuverters on the last two and the MM modules amplify the mixed output by 2.The MMx2 merges essential utilities into one powerful package, offering a CV mixer, attenuverters, signal amplification, offset generator, and a multiple, all in a compact form. Ideal for distributing modulations, creating complex mixers, generating stereo effects, and much more.The MMx2 is a testament to AtoVproject's dedication to creating instruments that allow you to express yourself and reward your understanding and exploration. To facilitate this, the MMx2 comes with a detailed manual full of inspirational patch ideas that will take your sound design to the next level.Dive into the world of advanced modulation manipulation with MMx2.Stay inspired! Stay innovative!Features:• Sold as a pair• 4 in 1 DC Mixer• Multiple MMs can be combined into a matrix mixer• Optimized for CV - Audio compatible• Input 1 and 2 have attenuators• Input 3 and 4 have attenuverters (polarizers)• Input 1 to 3 can be chained to the next module Input 4 is normalled to a voltage source so it can be used as offset controlDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€160.00*
Befaco - AC/DC (discontinued)
sold out at the moment
- - - - Discontinued - - - -AC/DC is a class-compliant DC coupled audio interface in Eurorack format. With its 6 HP, it is perfect for live performance and travel Rigs.Based on Rebel Technology OWL platform, It allows sending and receiving both CV and Audio at 16 Bits 48 kHz. as well as load patches from Rebel’s library.It is compatible with all popular DAW and CV generators, and also as an audio and CV processor for iOS apps.Features:• Class-compliant audio interface• DC coupled with range -10 to 10 V• Level meters and clip LEDs• 48 Khz 16 Bit• Compatible with OWL platform• Stm32H7 processor with 32 Mb of RAMDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€199.92*
Befaco - CV Thing
only 2 left
CV Thing is a fully mappable CV to MIDI converter in just 6HP. Its based on our VCMC module, but aiming for small and compact performance rigs. It has eight inputs that can be mapped to any MIDI message quite easily thanks to its simple and intuitive user interface. CCs, Program change ,V/Oct to Note or Clock are some of the messages that can be configured to easily control MIDI gear from your modular rig.Features:• Class-compliant USB MIDI and TRS connectors.• TRS to DIN5 Type A adaptor included.• 8 CV inputs.• Controls fully mappable to any MIDI message (CC, Notes, Program change, Clock, ST/SP, NRPN…)• Configurations are saved both in internal memory and via Sysex.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€176.12*
Befaco - Hexpander
available
Hexpander adds great functionality to Hexmix module. Featuring Three aux send with stereo returns, individual outputs for each channel, complete PFL system and balanced output.Hexpander is designed to be placed on top of Hexmix. Expanding Eurorack concept to 6U, allows every channel to be aligned as in traditional tabletop mixers.Features:• Three auxiliar sends with stereo returns and individual controls per channel.• Pre and Post Fader/EQ outputs.• Selectable Line/Modular level at return inputs.• Monitor section with PFL per channel.• Individual PostEq output per channel.• Master section with Headphones amp and balanced line outputsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€265.37*
Befaco - Joystick
only 2 left
A compact attenuverting (attenuator-inverter) joystick controller and Gate Generator. With it, you can generate and process two control voltages using only one hand. Provided controls for CV ranges and offset adjust the boundaries of your control, this way it never gets out of the desired range, ensuring sensibility and playability even with wild performance gestures.Features:• Robust arcade style joystick for manually generating either CV with Range and Offset control or attenuating two input signals• Two push buttons to generate gates manually.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€113.05*