Zlob Modular - Triple Cap Chaos

Product information "Zlob Modular - Triple Cap Chaos"
The Triple Cap Chaos(C^3 Chaos) is a 2hp analog, chaos based, noise oscillator, pseudo ring modulator/harmonics generator, and audio mangler.

It is a unique module, like the Diode Chaos, because it has never existed as a musical instrument until now. There is also no other module to my knowledge that can do exactly what the Triple Cap can do. The circuit(with several modifications) is based on the paper “Simple Autonomous Chaotic Circuits” by J.C. Sprott and Jessica R. Piper. As opposed to the Diode Chaos that generates control voltage this module focuses on the audio rate.

The “Emanate” potentiometer controls the coarser overall spectrum of the chaos, from lots of activity counter clock wise up to less chaos and more of a steady oscillation. The “Width, CV ATT” potentiometer can be thought of as more of a fine control for the chaos/oscillator. When something is inserted into the “CV” in the voltage normalization from the width knob is broken and the potentiometer now acts as an attenuator for the incoming cv. The Triple Cap is not a traditional volt per octave exponential VCO, and has a sort of narrow frequency range to exploit the chaotic behavior.

It expects a +5v to -5v max signal in to modulate the chaos. The “IN” jack is an A.C. coupled input for audio in, although cv and audio can work for both the “CV” in jack and “IN.” The “IN” will interfere and interact with the onboard chaotic oscillator depending on the frequency of the input, which may take some experimentation. It can create ring mod ish sounds, to added harmonics, to almost bit crushed sounds depending on the “X” or “Y” output. The “X” output is a more windy noisy sinusoidal based output and the “Y” output is more squared off and aggressive, harsher sounding output.

Some quirks about the Triple Cap: The “X” output can offset negatively or positively a little bit depending on the pot settings, but both outputs tend to stay around 10vpp. With the “Emanate” and “Width” pots all the way up the typical frequency will be around 150hz although some will reach 200hz at this setting. With the “Emanate” pot full counter clock wise “Width” pot full clock wise the frequency will be around 250hz. It is possible to send signals into the triple cap that can bring it out of the desired range causing the oscillation to cut out.

The Triple Cap has a double sided panel. meaning one side has the classic graphics and the other is Soulless with less graphics.

DIY-Kit-Type:
THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
Current draw +12 V [mA]: 15
Current draw -12 V [mA]: 10
DIY Level: Easy/Medium
Depth [mm]: 37
Width [HP]: 2
Format: 3U
Panel / Color: Black FR4
Manufacturer / Hersteller:
Żłob Modular
Keven Kalay
3117 N Springfield Ave
60618 Chicago, IL
USA
zlobmodular@gmail.com

EU responsible:
Tech Creation Lab Leipzig UG (haftungsbeschränkt)
Nonnenstrasse 19
04229 Leipzig, Germany
support@exploding-shed.com
WEEE-Nr.: DE94097895"


Product Safety Information

Eurorack DIY Kits

Important Notice & Intended Use
Please read this safety guide before installation or use. This kit is intended for adult users experienced in electronics and modular synthesis. Assembly, including soldering, is required. Proper testing and installation are essential to ensure safe and functional operation. The completed module is intended for installation in a Eurorack-compatible synthesizer system powered by ±12V and +5V.

General Warnings

1. Electrical Hazards:
• Ensure the power supply matches the module’s specified voltage and current ratings (refer to the product manual). Incorrect voltage can damage the module and pose a safety risk.
• Never connect or disconnect the module while the Eurorack system is powered on.
• Wrong polarity can damage your module or system. Make sure the module is connected with correct polarity.

2. Heat Generation:
• The module may generate heat during operation. Ensure proper ventilation within your Eurorack case to prevent overheating.

3. Sharp Edges:
• The module’s faceplate and components may have sharp edges. Handle with care to avoid cuts or scratches.

4. Small Parts:
• Contains small parts that could cause a choking hazard. Keep away from children and pets.

5. Compatibility:
• This module is designed specifically for Eurorack-compatible systems. Connecting it to non-compatible systems may result in damage or malfunction.

Assembly Requirements
• Soldering skills are required to complete the module.
• Ensure a clean, well-lit and ventilated workspace free of flammable materials during assembly.
• Use appropriate tools and safety equipment, such as eye protection.

Testing
• Test the module thoroughly for shorts or incorrect assembly before powering it in your Eurorack system. When the unit has malfunctions due to incorrect assembly, the entire Eurorack system might be damaged. It's a good idea to test it in a separate case with only that single module.
• Use a multimeter or other appropriate tools to confirm proper functionality.

Installation and Use
• Mount securely in a Eurorack case using the provided screws.
• Use only the included or manufacturer-recommended power cable.
• Connect only when the power is off.
• Follow the module's user guide for instructions on operation. Do not exceed the input/output limits specified.

Responsibility
Users are solely responsible for proper assembly and testing. Contact manufacturer support for assistance if needed.

Environmental Safety
• Dispose of the module, its components, and packaging in accordance with local electronic waste regulations.

Liability Disclaimer
• The manufacturer or distributor is not responsible for any injury, damage, or malfunction resulting from improper installation, use, or modification of this product.

Contact Information
For further assistance, contact the manufacturer (you'll find the info under each product in our shop) or our shop support team at:

Tech Creation Lab Leipzig UG (haftungsbeschränkt)
Nonnenstrasse 19, 04229 Leipzig, Germany
support@exploding-shed.com
Manufacturer "Zlob Modular"

Żłob Modular is a, Chicago Illinois based, manufacturer specializing in analog electronics in the Eurorack format. Since 2015, he continues to design ornate looking, compact modular synthesizers from fundamental utilities to unique Chaos based modules capable of differential equation solving to modules for harsh noise experimentation. Żłob is run by founder/designer, artist/musician Keven Michael-Onur Kalaycıoğlu-Żłobnicki.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.