Wirehead Instruments - Basilisk (Assembled)
Product number:
100050
Product information "Wirehead Instruments - Basilisk (Assembled)"
This is the assembled version of this synth with red LEDs! Basilisk is a new bass-line exploration synthesizer from Wirehead Instruments, with dual digital oscillators driven into an aggressive MS20-style analog filter coupled with a powerful generative sequencer.
Whether you need thumping bass-lines, melodic leads, or percussive tribal beats, the Basilisk is ready to lead you down the rabbit hole from the moment you power it on.
The dual oscillators include saw and square/pulsewave, with manual & LFO control over PWM, detune, pitch envelope & glide.
The analog filter has a fat saturated drive stage with resonance that can go from subtle to squelching to screaming, and the external audio input can process instruments from your desktop or Eurorack
All of this can be sequenced and modulated by the attack/decay exponential envelope, multi-waveform/multi-destination LFO and Elektron-style parameter-locks.
The Basilisk is powered by a 1-16-step generative sequencer evolved from the Freaq FM, with multiple algorithms. Explore deep space, underground caverns, deep jungle or 1980s suburbia!
Features:
Oscillators
• 2 digital oscillators - saw, square & pulse
• De-tune control that always stays musical, from light flanger to rich chorus, dial it up for fat fifths and octaves
Analog Filter
• MS20-style 12dB resonant multi-mode filter
• Analog filter drive from -20dB to +20dB saturated overdrive
• Low-pass and non-resonant high-pass mode
• Digitally-controlled cuttoff modulation
• External audio input accepting wide range of signals from 1v p-p to 10vp-p
Modulation
• Attack/Decay envelope with shape control, routable to filter cutoff and/or pitch
• LFO with multiple waveforms and configurable destination: cutoff, envelope (attack, decay or depth), note • length, PWM, detune, octave or sequence length
• 6 modulation lanes with full 16-step parameter-lock recording of synth parameters
Generative Sequencer
• Generative sequencer with 1-16 steps
• Multiple generative algorithms including scale-notes, runs, scale-arpeggio, call/response
• Sequence mutates/evolves at user-defined rate & note-density
• Selectable tonic, octave & scale
• Tap-tempo control
• Analog sync input & output (Volca, PO or Eurorack compatible with 1/2/4 steps per pulse)
Patch Memory
• Persistent patch memory saving all digital synth and sequence parameters
Hardware
• Mono audio output (32KHz 14-bit DAC, 4v p-p)
• Sync input / output (0-5V rising-edge)
• Audio Input (1v p-p to 10vp-p)
• Powered by an Arduino Nano V3!
• 142m (w) x 100mm (d) x 40mm (h)
• 9-12V DC or micro USB powered (70mA @ 12VDC)
DIY-Kit-Type:
THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
Whether you need thumping bass-lines, melodic leads, or percussive tribal beats, the Basilisk is ready to lead you down the rabbit hole from the moment you power it on.
The dual oscillators include saw and square/pulsewave, with manual & LFO control over PWM, detune, pitch envelope & glide.
The analog filter has a fat saturated drive stage with resonance that can go from subtle to squelching to screaming, and the external audio input can process instruments from your desktop or Eurorack
All of this can be sequenced and modulated by the attack/decay exponential envelope, multi-waveform/multi-destination LFO and Elektron-style parameter-locks.
The Basilisk is powered by a 1-16-step generative sequencer evolved from the Freaq FM, with multiple algorithms. Explore deep space, underground caverns, deep jungle or 1980s suburbia!
Features:
Oscillators
• 2 digital oscillators - saw, square & pulse
• De-tune control that always stays musical, from light flanger to rich chorus, dial it up for fat fifths and octaves
Analog Filter
• MS20-style 12dB resonant multi-mode filter
• Analog filter drive from -20dB to +20dB saturated overdrive
• Low-pass and non-resonant high-pass mode
• Digitally-controlled cuttoff modulation
• External audio input accepting wide range of signals from 1v p-p to 10vp-p
Modulation
• Attack/Decay envelope with shape control, routable to filter cutoff and/or pitch
• LFO with multiple waveforms and configurable destination: cutoff, envelope (attack, decay or depth), note • length, PWM, detune, octave or sequence length
• 6 modulation lanes with full 16-step parameter-lock recording of synth parameters
Generative Sequencer
• Generative sequencer with 1-16 steps
• Multiple generative algorithms including scale-notes, runs, scale-arpeggio, call/response
• Sequence mutates/evolves at user-defined rate & note-density
• Selectable tonic, octave & scale
• Tap-tempo control
• Analog sync input & output (Volca, PO or Eurorack compatible with 1/2/4 steps per pulse)
Patch Memory
• Persistent patch memory saving all digital synth and sequence parameters
Hardware
• Mono audio output (32KHz 14-bit DAC, 4v p-p)
• Sync input / output (0-5V rising-edge)
• Audio Input (1v p-p to 10vp-p)
• Powered by an Arduino Nano V3!
• 142m (w) x 100mm (d) x 40mm (h)
• 9-12V DC or micro USB powered (70mA @ 12VDC)
DIY-Kit-Type:
THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
| DIY Level: | Medium |
|---|---|
| Depth [mm]: | 100 |
| Height [mm]: | 40 |
| Material / Color: | Black FR4 |
| Power Input Type (pri.): | 9 Vdc / Barrel (5,5/2,1) |
| Power Input Type (sec.): | micro USB |
| Width [mm]: | 142 |
Manufacturer / Hersteller:
Wirehead Instruments
Andrew Row
PO Box 1001
6910 Claremont, WA
Australia
support@wireheadinstruments.com
EU responsible:
Tech Creation Lab Leipzig UG (haftungsbeschränkt)
Nonnenstrasse 19
04229 Leipzig, Germany
support@exploding-shed.com
WEEE-Nr.: DE94097895
Product Safety Information
Desktop / Standalone DIY Kits
Important Notice & Intended Use
Please read this safety guide before installation or use. This kit is intended for adult users experienced in electronics and modular synthesis. Assembly, including soldering, is required. Proper testing and installation are essential to ensure safe and functional operation. The completed product is intended as a desktop / standalone unit and is powered by an external DC power supply between +5V and +18V, depending on the specific unit.
General Warnings
2.1. Electrical Hazards:
• Ensure the power supply matches the module’s specified voltage and current ratings (refer to the product manual). Incorrect voltage can damage the module and pose a safety risk.
• Wrong polarity can damage your synth, make sure the unit is connected with correct polarity.
2.2. Heat Generation:
• The module or power supply may generate heat during operation. Do not cover one of them.
2.3. Sharp Edges:
• The module’s faceplate and components may have sharp edges. Handle with care to avoid cuts or scratches.
2.4. Small Parts:
• Contains small parts that could cause a choking hazard. Keep away from children and pets.
2.5. Compatibility:
• This module is designed specifically for usage with other devices that operate on Eurorack- or line-level. Connecting it to non-compatible systems may result in damage or malfunction.
Assembly Requirements
• Soldering skills are required to complete the unit.
• Ensure a clean, well-lit and ventilated workspace free of flammable materials during assembly.
• Use appropriate tools and safety equipment, such as eye protection.
Testing
• Test the module thoroughly for shorts or incorrect assembly before powering it up. When the unit has malfunctions due to incorrect assembly, the unit or power supply might be damaged.
• Use a multimeter or other appropriate tools to confirm proper functionality.
Installation and Use
• Use only the included or manufacturer-recommended power cable and/or powerr supply.
• Follow the module's user guide for instructions on operation. Do not exceed the input/output limits specified.
Responsibility
Users are solely responsible for proper assembly and testing. Contact manufacturer support for assistance if needed.
Environmental Safety
• Dispose of the module, its components, and packaging in accordance with local electronic waste regulations.
Liability Disclaimer
• The manufacturer or distributor is not responsible for any injury, damage, or malfunction resulting from improper installation, use, or modification of this product.
Contact Information
For further assistance, contact the manufacturer (you'll find the info under each product in our shop) our shop support team at:
Tech Creation Lab Leipzig UG (haftungsbeschränkt)
Nonnenstrasse 19, 04229 Leipzig, Germany
support@exploding-shed.com
Wirehead Instruments
Andrew Row
PO Box 1001
6910 Claremont, WA
Australia
support@wireheadinstruments.com
EU responsible:
Tech Creation Lab Leipzig UG (haftungsbeschränkt)
Nonnenstrasse 19
04229 Leipzig, Germany
support@exploding-shed.com
WEEE-Nr.: DE94097895
Product Safety Information
Desktop / Standalone DIY Kits
Important Notice & Intended Use
Please read this safety guide before installation or use. This kit is intended for adult users experienced in electronics and modular synthesis. Assembly, including soldering, is required. Proper testing and installation are essential to ensure safe and functional operation. The completed product is intended as a desktop / standalone unit and is powered by an external DC power supply between +5V and +18V, depending on the specific unit.
General Warnings
2.1. Electrical Hazards:
• Ensure the power supply matches the module’s specified voltage and current ratings (refer to the product manual). Incorrect voltage can damage the module and pose a safety risk.
• Wrong polarity can damage your synth, make sure the unit is connected with correct polarity.
2.2. Heat Generation:
• The module or power supply may generate heat during operation. Do not cover one of them.
2.3. Sharp Edges:
• The module’s faceplate and components may have sharp edges. Handle with care to avoid cuts or scratches.
2.4. Small Parts:
• Contains small parts that could cause a choking hazard. Keep away from children and pets.
2.5. Compatibility:
• This module is designed specifically for usage with other devices that operate on Eurorack- or line-level. Connecting it to non-compatible systems may result in damage or malfunction.
Assembly Requirements
• Soldering skills are required to complete the unit.
• Ensure a clean, well-lit and ventilated workspace free of flammable materials during assembly.
• Use appropriate tools and safety equipment, such as eye protection.
Testing
• Test the module thoroughly for shorts or incorrect assembly before powering it up. When the unit has malfunctions due to incorrect assembly, the unit or power supply might be damaged.
• Use a multimeter or other appropriate tools to confirm proper functionality.
Installation and Use
• Use only the included or manufacturer-recommended power cable and/or powerr supply.
• Follow the module's user guide for instructions on operation. Do not exceed the input/output limits specified.
Responsibility
Users are solely responsible for proper assembly and testing. Contact manufacturer support for assistance if needed.
Environmental Safety
• Dispose of the module, its components, and packaging in accordance with local electronic waste regulations.
Liability Disclaimer
• The manufacturer or distributor is not responsible for any injury, damage, or malfunction resulting from improper installation, use, or modification of this product.
Contact Information
For further assistance, contact the manufacturer (you'll find the info under each product in our shop) our shop support team at:
Tech Creation Lab Leipzig UG (haftungsbeschränkt)
Nonnenstrasse 19, 04229 Leipzig, Germany
support@exploding-shed.com
Manufacturer "Wirehead Instruments"
“Wireheading is the act of directly triggering the brain's reward center by electrical stimulation of an inserted wire, for the purpose of 'short-circuiting' the brain's normal reward process and artificially inducing pleasure.”
With a lifelong passion for music and technology, I have been designing and building synthesizers, modules and noise machines in my home studio since 2020.
Combining a background in electronics assembly and software development with many years as an acoustic and electronic musician, I have long since bored all my family and friends with endless bleeps&bloops, so I started publishing to share my music/noise with a wider audience. I quickly learned that the world does not need many more 10-minute-long DAWless jams but there are lots of people interested in fun noisy music machines and projects!
In 2023, Meebleeps Machines became “Wirehead Instruments” to reflect the primary purpose of these tools - artificially induced pleasure!
Login