ADDAC System - 214 VC Rotator
available
This is our VC Rotator, a stepped routing module for any type of signal (audio, cv, gate, trigger...)Similar to a VC switcher but in this case there's the same number of inputs as outputs so, instead of 4 to 1 or 1 to 4, this module is always 4 to 4 but it can be patched for 2 to 2 and 3 to 3 step actions.All four inputs get routed to the four outputs depending on the CV and Clock controls and are divided into 4 routing steps:1. routes all inputs to the same number output: 1:1, 2:2, 3:3, 4:42. routes all inputs to an offset of 1: 2:1, 3:2, 4:3, 1:43. routes all inputs to an offset of 2: 3:1, 4:2, 1:3, 2:44. routes all inputs to an offset of 3: 4:1, 1:2, 2:3, 3:4Direction determines if the clock input goes forward or backwards.Going forward it can be set to 2-3 or 4 steps using the Rotate knob offset, going backwards always sync to 4 steps even if offseted by the Rotate knob.For 2 & 3 step action input 1 is normalled to input 3 and input 2 is normalled to input 4.Reset resets the internal clock to the first step.Pendulum, external sequencing or any complex CV actions can be achieved using the CV input and dedicated attenuverter.4 LEDs monitor which input is routed to output 1.Features:• 4 Inputs• 4 Outputs• Direction Switch• CV Rotate with Attenuverter• Clock and Reset Inputs• 4 Monitor LedsDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€145.00*
ADDAC System - 304 Manual Gates
available
With the ADDAC304 Manual Gates you'll be getting 8 manual gates (0 +5v) in a nifty package - a perfect way to perform on and control your modular system.The ADDAC304 comes with an interesting twist: 4 out of the 8 available gates can act as momentary switches, outputting the signals in their respective inputs when each gate’s button is pressed.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€75.00*
ADDAC System - 305 Manual Latches
available
The ADDAC305 Manual Latches is a combination of 8 manual latching switches in a small and elegant module: each button toggles between Gate high / Gate low when pressed, outputting a 5V gate signal. Additionally, 4 of the 8 available latches sport inputs and can act as manual latching switches, allowing the incoming signal to pass to the output when the button is toggled.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€90.00*
Befaco - Muxlicer
available
Muxlicer is a sequential signal processor designed for add a huge range of special functions to your modular setup in the minimum space.Is divided in three main blocks: a Digital Step Controller, a Gate Generator and an Analog Switch (a.k.a. Mux/DeMux)The module is designed with high “function to HP ratio” philosophy , to have maximum flexibility in minimum space.An analog switch is a device capable of switching or routing analog signals. In the case of Muxlicer, the switch is reversible, so you can send 8 different signals to 1 destination and viceversa.Through Common I/O you can either send a signal to the Mux I/Os or receive a signal from them. (Depending on how the module is connected). It is also used as CV Out when nothing is connected to “All In” or “Mux I/Os”. The eight Mux I/Os are normalled to “All In” jack, so any signal present at this input will go to all of them.Imagine you want to send a signal to steps 1,2,4,5,6 and 8 and two more signals to 3 and 7 respectively. You just need three wires for this: plug the first one to All In and the other two to 3 and 7 Mux I/Os and you are done!Features:• Route any modular signal from one IN up to eight different Outs or vice versa.• Generate CV and Gate signals, been able to work as sequential voltage source a.k.a. sequencer.• Cut audio signals in rhythmical slices with independent volume.• Generate complex and dynamic patterns from any audio or modulation signal.• Create powerful Gate sequences with control voltage retriggering for each step.• Select easily when your signals act on your patch with the Address function.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€146.37*
Befaco / Molten Modular - Molten Bypass
available
This is our new collaboration with Robin Vincent aka Molten Music Technology. A Stereo bypass module to gate control the send of your signals to your favorite effect!Molten bypass features a hard/soft bypass control, to hard cut the return of your effect or allow the long tails of your reverb to stay after you bypass the effect. Also a gate/latch control to use either triggers or gates for control and a gain control for the returned signal.Features:• Full stereo signal path• DC coupled• Hard or soft bypass selection• Gate or Latch possibility• Manual or Gate control• Gain control over the returnDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€100.00*
Jolin – Rosa
available
ROSA is a multi-mode crossfader, scanner, and switcher that allows seamless morphing between up to four inputs and outputs. With its three operating modes (Scan, Wave, and Pass), you can easily shape and route signals to fit any patch.Features:• Scan Mode: Morph between up to four inputs with adjustable curves using the KNEE control.• Wave Mode: Independently control the four VCAs for complex dynamic changes.• Pass Mode: Route a single input (or mix multiple inputs) to up to four outputs, perfect for quadraphonic setups or parallel processing.• Infinite Analogue Potentiometer: For smooth, continuous transitions.• Global SHUT Control: CV-controlled mute for immediate silence.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€222.00*
Zlob Modular - Entropy Expander (Panel PCB)
available
This is the panel PCB version of this kit.Analog random voltage and noise generator that expands upon the features of the Entropy Euroack Module in 3 HP.The Entropy+Expander packs together some of the most random voltage options in 6 HP. It provides a controllable “Glide” (slew) out for the S/T\H, a comparator with a controllable rate (“Thrsh”) of random gates (“Rand Gate”) out with an input to compare other waveforms (Comp In, inserting a cable into here breaks the white noise normalization), and high pass filtered white noise resulting in approximate “Blue noise” (+3db/octave) and “Violet noise” (+6db/octave) outs.The unique part of the circuit is a voltage controlled A/B switch thats normalled to the “Rand Gate” out that’s switching between the S/T\H out (left Blue led window) and Infra out (right Red led window), the Glide control also effects the S/T\H coming out of the switch so you can get really random results from the “Entropy Out.” Inserting a cable into “Switch CV In” breaks the random gate normalization and lets you toggle between A/B (left S/T\H out and right Infra out, indicated by the led windows) with your own gate or trigger.There is a jumper on the pcb to select if you want glide on the S/T\H at, Entropy out, or un-slewed operation. There is also a trimmer for setting the amplitude of the incoming signal at “Comp In” which sets the frequency range of random gates. This may have to be adjusted depending on your Entropy version. The random gate range can also be set up more as a noise oscillator by turning the pcb trim (clockwise) up or it can be set so random gates are extremely slow (trim counter clockwise) with minutes between random gates.DIY-Kit-Type:Panel/PCB Kit. This is a do-it-yourself panel/PCB kit, no parts are supplied, you will need to source them yourself.
€27.00*
Zlob Modular - Push VCA (Panel PCB)
available
This is the panel PCB version of this kit.The Push VCA is a 2 Channel DC Coupled Mute Eurorack Module in 2 HP. It features 2 independent unity gain DC coupled VCAs with led push button mutes. A mix of both channels is available at the sum, but all outputs are available simultaneously. The newest version has normalizations to +5v, so with nothing plugged into the ins voltage can be toggled on and off at the outputs and up to 10 volts can be output at the sum. The buttons are latching, not momentary push buttons. LED button color may vary, but it will always be two of the same color.DIY-Kit-Type:Panel/PCB Kit. This is a do-it-yourself panel/PCB kit, no parts are supplied, you will need to source them yourself.
€25.00*