Products of AtoVproject
AtoVproject is a Berlin based manufacturer that has strong ties with the local synthesizer community. AtoVproject aims at creating units that last a lifetime while also being as sustainable as possible, therefore great effort is put into the quality of our products.
AtoVproject - 16n Rework (Black)
only 1 left
The 16n AtoVproject Rework is aimed at solving a problem very specific to modular synthesis. As a patch is getting more and more complex a forest of cables has grown over your system before you know it. This module allows you to take the control from the modular into a very ergonomic controller that integrates perfectly into a modern studio.The 16n AtoVproject Rework is a controller sending CV, I2C, MIDI jack, USB MIDI (compatible PC, Mac, iPad etc...), making it the absolute ultimate controller for any of your hardware and software all in one!Even better this controller can either be used as a Eurorack module or as a standalone unit using the beautiful aluminum enclosure.In 2019, the Berlin Modular community showed interest in building the 16n Faderbank. As one of the Berlin Modular community organizers, I decided to make a redesign of the 16n faderbank following the suggestions and desires of our members. The 16n AtoVproject Rework is the result.Features:• 16 high-end Alps faders• Eurorack compatible (50hp) and standalone enclosure (for use in or out of the rack)• Selectable 0-5V or 0-10V CV output range (independent setting for each fader)• High stability power conditioning for high stability analog outputs• Soft MIDI thru. MIDI data sent to the 16n through USB is echoed to the MIDI jack (Since firmware v2.1.0)• Utility connector on the back of the unit to simplify the use of i2c with modules like the ER301DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€279.00*
AtoVproject - 16n Rework (Silver)
sold out at the moment
The 16n AtoVproject Rework is aimed at solving a problem very specific to modular synthesis. As a patch is getting more and more complex a forest of cables has grown over your system before you know it. This module allows you to take the control from the modular into a very ergonomic controller that integrates perfectly into a modern studio.The 16n AtoVproject Rework is a controller sending CV, I2C, MIDI jack, USB MIDI (compatible PC, Mac, iPad etc...), making it the absolute ultimate controller for any of your hardware and software all in one!Even better this controller can either be used as a Eurorack module or as a standalone unit using the beautiful aluminum enclosure.In 2019, the Berlin Modular community showed interest in building the 16n Faderbank. As one of the Berlin Modular community organizers, I decided to make a redesign of the 16n faderbank following the suggestions and desires of our members. The 16n AtoVproject Rework is the result.Features:• 16 high-end Alps faders• Eurorack compatible (50hp) and standalone enclosure (for use in or out of the rack)• Selectable 0-5V or 0-10V CV output range (independent setting for each fader)• High stability power conditioning for high stability analog outputs• Soft MIDI thru. MIDI data sent to the 16n through USB is echoed to the MIDI jack (Since firmware v2.1.0)• Utility connector on the back of the unit to simplify the use of i2c with modules like the ER301DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€279.00*
AtoVproject - cDVCA (Black)
available
cDVCA or class-D VCA is a new kind of VCA based on an entirely novel concept that is inspired from class-D amplification technology. This is not a transparent VCA and brings a lot of character to the sound.The first VCA that tracks 1V/octConcept: The input signal is turned into an ultrasonic PWM signal (~34kHz). The PWM is scaled to the desired amplitude and then filtered back down to the original signal.The twist: The PWM frequency can be lowered down into the audio spectrum and the frequency can be controlled via its 1V/oct input allowing for crazy waveshaping that tracks your melodies.The drive controls an innovative clipping method that does not rely on overdriving any circuitry and therefore results in distortions with a very defined character.The signal then goes into a 1 pole VCF/tone circuit that allows to keep things under some amount of control as the harmonics produced by this module can be very aggressive.With no input the module generates a simple square wave and therefore can be used a simple synth voice (VCO→VCA-VCF)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€185.00*
AtoVproject - cDVCA (Silver)
only 2 left
cDVCA or class-D VCA is a new kind of VCA based on an entirely novel concept that is inspired from class-D amplification technology. This is not a transparent VCA and brings a lot of character to the sound.The first VCA that tracks 1V/octConcept: The input signal is turned into an ultrasonic PWM signal (~34kHz). The PWM is scaled to the desired amplitude and then filtered back down to the original signal.The twist: The PWM frequency can be lowered down into the audio spectrum and the frequency can be controlled via its 1V/oct input allowing for crazy waveshaping that tracks your melodies.The drive controls an innovative clipping method that does not rely on overdriving any circuitry and therefore results in distortions with a very defined character.The signal then goes into a 1 pole VCF/tone circuit that allows to keep things under some amount of control as the harmonics produced by this module can be very aggressive.With no input the module generates a simple square wave and therefore can be used a simple synth voice (VCO→VCA-VCF)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€185.00*
AtoVproject - cLFO
available
Introducing our innovative Complex Low Frequency Oscillator (cLFO) - The cLFO is an instrument for those who believe in pushing the limits of modulation. Featuring two CV-controlled LFOs that intricately intermodulate and are seamlessly integrated with a ring modulator, this module elevates your synthesis and sound design to unprecedented levels.Crafted with a focus on cross and self-patching, the cLFO invites you to explore the endless possibilities of modulation. Dive into creating continuously variable waveforms, exponential shapes, bouncing ball effects, immersive stereo soundscapes and many other sonic wonders!Each LFO outputs Triangle, Saw, and Square waves. The Triangle output of LFO1 is normalled to the CV input of LFO2 with attenuation. The addition of a ring modulator to this setup draws from years of the designer's own experimental projects. It is an invitation to experiment with effects traditionally reserved for audio in the realm of modulation. A ring modulated LFO delivers the rhythmical essence of a conventional LFOs but with an added complexity and variability that ensures your soundscapes are always evolving.This module offers an expansive modulation frequency range, with speed adjustments from as slow as 2 minutes per cycle to as fast as 20 cycles per second. With CV control, frequencies can stretch from 13 hours per cycle to 400 cycles per second, ensuring unparalleled versatility in your modulation explorations.Accompanying the cLFO is a detailed manual filled with lots of patch idea designed to elevate your sound design skills to new levels.Dive into the world of advanced modulation manipulation with cLFO.Stay inspired! Stay innovative!Features:• Two analog LFOs• Control voltage over LFO frequency• 3 waveform outputs per LFO: Triangle, Square and Sawtooth (LFO1 - ramp down; LFO2 ramp up)• Wide frequency range: 2 minutes - 0.05s (20Hz) without CV and 13 hours to 400Hz with CV• Ring Modulator (aka four quadrant multiplier aka bipolar VCA)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€190.00*
AtoVproject - Gaeto (Black)
available
The AtoVproject Gaeto is a new type of clocked logic module. Gaeto is a great module to play around with triggers, gates and legatoes turning one into the other. As a result we decided to name the module Gaeto from “Gate” and “Legato”.The Gaeto’s function is to perform the following operation:“If the signal on the data input has been high, then the output is high at the next clock. If not - the non-output is high.”In other words, if the signal on the input signal goes over 1V then the memory stores a 1 if not it stores a 0. At the next clock the output will be high if a 1 was stored and the non output will be high if a 0 was stored.The output is coupled with an AND gate that allows for the outputs to either follow the pulse width of the clock or be maintained high until the next clock. This function is also CV controllable for interesting rhythm modulations.This rather obscure function allows for an extremely wide range of uses. This is a module that rewards exploration.Additionally, multiple Gaetos can be chained together using the included cable to create shift register functions.This design relies on CMOS CD4000 series ICs (4013 and 4081). These were selected for their reliability, high speed and low power consumption.Features:• /2 /3 Clock divider• Legato generator• Trigger to gate converter• Rhythm quantizer• Sub octave generator with PWM• Generative trigger sequenceDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€87.00*
AtoVproject - Gaeto (Silver)
only 1 left
The AtoVproject Gaeto is a new type of clocked logic module. Gaeto is a great module to play around with triggers, gates and legatoes turning one into the other. As a result we decided to name the module Gaeto from “Gate” and “Legato”.The Gaeto’s function is to perform the following operation:“If the signal on the data input has been high, then the output is high at the next clock. If not - the non-output is high.”In other words, if the signal on the input signal goes over 1V then the memory stores a 1 if not it stores a 0. At the next clock the output will be high if a 1 was stored and the non output will be high if a 0 was stored.The output is coupled with an AND gate that allows for the outputs to either follow the pulse width of the clock or be maintained high until the next clock. This function is also CV controllable for interesting rhythm modulations.This rather obscure function allows for an extremely wide range of uses. This is a module that rewards exploration.Additionally, multiple Gaetos can be chained together using the included cable to create shift register functions.This design relies on CMOS CD4000 series ICs (4013 and 4081). These were selected for their reliability, high speed and low power consumption.Features:• /2 /3 Clock divider• Legato generator• Trigger to gate converter• Rhythm quantizer• Sub octave generator with PWM• Generative trigger sequenceDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€87.00*
AtoVproject - lx-euclid
available
The AtoVproject lx-euclid is a 4-channel trigger sequencer with a standout feature: two touch-sensitive rings that redefine hands-on control. These rings, paired with full color circular display, offer an unparalleled, intuitive interface designed for fast, real-time performance. The touch rings make it incredibly easy to interact with your sequences, allowing you to apply mutes, fills, and resets on the fly. This immediate tactile response puts creative control directly at your fingertips, making it perfect for both live improvisation and studio work.In addition to its touch-sensitive rings, the lx-euclid boasts 4 assignable CV inputs, probability settings, and 8 save slots, offering endless possibilities for pattern creation and variation. The module also introduces new twists on traditional Euclidean rhythms, with Exponential, Inverse Exponential, and Mirrored Exponential algorithms for even more flexibility and evolving beats. Whether you're looking to unlock new creative possibilities or elevate your live set, the lx-euclid’s touch rings bring a whole new level of expression to your modular rig.Features:• Four trigger sequencers • Two touch capacitive rings• Performance macro (Mute, Fill, Reset, etc)• 4 fully assignable CV inputs (+/-5V input range)• 4 rhythm generative algorithms• 8 save slotsDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€249.00*
AtoVproject - MMx2
available
Expand the power of your modulations with the MMx2, a dual-pack module designed to bring flexibility and creativity into your system. Each MMx2 package contains a pair of MM modules.Sold as a pair, MM modules can function as two separate units or be linked for expanded matrix mixing capabilities. Connect even more MM modules to increase the power of your Eurorack synthesiser!Every MM module has attenuator on the first two inputs and attenuverters on the last two and the MM modules amplify the mixed output by 2.The MMx2 merges essential utilities into one powerful package, offering a CV mixer, attenuverters, signal amplification, offset generator, and a multiple, all in a compact form. Ideal for distributing modulations, creating complex mixers, generating stereo effects, and much more.The MMx2 is a testament to AtoVproject's dedication to creating instruments that allow you to express yourself and reward your understanding and exploration. To facilitate this, the MMx2 comes with a detailed manual full of inspirational patch ideas that will take your sound design to the next level.Dive into the world of advanced modulation manipulation with MMx2.Stay inspired! Stay innovative!Features:• Sold as a pair• 4 in 1 DC Mixer• Multiple MMs can be combined into a matrix mixer• Optimized for CV - Audio compatible• Input 1 and 2 have attenuators• Input 3 and 4 have attenuverters (polarizers)• Input 1 to 3 can be chained to the next module Input 4 is normalled to a voltage source so it can be used as offset controlDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€160.00*